Ultra-Shear Pen Mill Ci Carbide Inserts for Amazing Tool Life and Cleaner Cuts
IMPORTANT NOTE: This is a very sharp and effective tool and should only be used in a drill-press. DO NOT hand hold this tool as it can cause serious injury.
Creating beautiful turned pens starts with carefully preparing the turning blank. Every pen kit on the market includes a brass insert tube that has to be glued into the blank. Then the blank needs to be trimmed perpendicular to and perfectly flush with both ends of the insert tube. The trimming process is fundamentally important to great results, but until now, the tools available to pen turners for that job have left a lot to be desired. Now Woodpeckers is introducing the Ultra-Shear Pen Mill Ci, a pen mill that effortlessly cuts every material pen turners use and through mountains of pen blanks.
The Ultra-Shear Pen Mill Ci uses razor-sharp nano-grain carbide inserts mounted in a precision-machined milling head. These are exactly the same inserts used on our Ultra-Shear Pen Size Square turning tools. The special long-life carbide edges will shave through exotic hardwoods, acrylics, polymers, stabilized woods, cast hybrids and even non-ferrous metals with flawless results. When the edges finally get dull, fresh cutting edges are as simple as loosening two screws, turning the inserts 90 degrees and locking them back down. Not only do you have sharper, longer lasting cutting edges, the head is also significantly larger than any other on the market, which means after trimming a 3/4" square pen blank, theres no annoying "halo" of material.
Keeping the milling head perpendicular to the brass insert tube requires a pilot shaft that is carefully sized to fit the tube just right neither too tight nor too loose. The new Ultra-Shear Pilot-Reamers are cut on precision Swiss lathes to exacting tolerances. We offer the 12 most popular sizes covering virtually every pen kit on the market. In addition to keeping the milling head perpendicular to the tube, the noses of the Pilot-Reamers are fluted to carefully cut away any glue residue or brass burrs inside the insert tube.
Competitive pen mills drive off the pilot shaft, relying only on the set screw to prevent the cutting head from spinning. The part that fits into your drill chuck on the Ultra-Shear Pen Mill Ci is part of the head, and has a 3-flat design that gives you a very positive lock when you tighten your chuck.
If you turn several different pen styles, we offer two sets. The 5-piece set includes the Pen Mill Ci and the four most popular Pilot-Reamers. The 13-piece set includes the Pen Mill Ci and all 12 Pilot-Reamers. Both sets come in a Woodpeckers plastic case with a custom cut foam liner to keep everything safe and organized. If you only make one or two style pens, you can buy the Pen Mill Ci milling head and just the Pilot-Reamers you need.
This product is the The 13-piece set, which includes:
- Pen Mill Ci
- 7mm Reamer
- Letter "O" Reamer
- 3/8" Reamer
- 25/64" Reamer
- 10mm Reamer
- 10.5mm Reamer
- 27/64" Reamer
- 11mm Reamer
- 15/32" Reamer
- 31/64" Reamer
- 12.5mm Reamer
- 33/64" Reamer
Shipping Charges and Policies
In United States (including Alaska and Hawaii): $7.99 flat rate charge per order. Packages will be sent by UPS,priority mail or first-class mail at the company's discretion based on weight and value. All packages are insured. Premium services such as UPS next day or second day shipments will be billed at actual charges plus the $7.99 flat rate fee.
Now Offering Free Shipping on orders of $250 or more. Free standard shipping is eligible on all orders of $250.00 or more being shipped to addresses in the United States including Alaska and Hawaii. Shipping / Taxes do not count toward the $250.00 qualification. Item(s) must equal up to $250.00 or more. There will be no special code to receive the free shipping but you must select FREE SHIPPING as the shipping option during checkout.
Alaska and Hawaii: All packages will be sent by priority mail insured. Actual charges plus the $7.99 flat rate charge will be billed at time of shipment. We can also ship UPS next day and 2nd day service at additional charges.
Canada: Canadian Shipping is $24.95 and is subject to certain limitations described below. Method: All Canadian orders are shipped via United States Postal Service, International Flat Rate. Time: Most Canadian orders are shipped within 1 business day after the payment for your order is received. Orders that do not meet the limitations described below, will delay shipping. Limitations: Canadian orders are shipped in a Flat Rate Envelope. A box is placed inside this envelope and the maximum dimensions of the box are 9 x 6 x 2 inches. Also, the entire package cannot weigh more than 4 pounds. If your order is too large for a single box, We will contact you to see if you would like to pay for an additional package. Additional packages are $24.95 each. Insurance: Insurance is available for Canadian orders and can be purchased by stating in the comment section during checkout, we will email with additional costs. The Berea Hardwoods Co. Inc. assumes no liability for orders after they have been mailed. We can also ship UPS service at additional charges.
Duties/Tarrifs/Fees/Etc All duties, tarrifs, and any other fees imposed by the local government and/or postal system are the sole responsibility of the buyer.
If you are in Europe you may order from our distributor at:
All Other Countries. Foreign (non-Canadian) Shipping is $35.95 and is subject to certain limitations described below. Method: All Foreign (non-Canadian) orders are shipped via United States Postal Service, International Flat Rate. Time: Most Foreign (non-Canadian) orders are shipped within 1 business day after the payment for your order is received. Orders that do not meet the limitations described below, will delay shipping. Limitations: Foreign (non-Canadian) orders are shipped in a Flat Rate Envelope. A box is placed inside this envelope and the maximum dimensions of the box are 9 x 6 x 2 inches. Also, the entire package cannot weigh more than 4 pounds. If your order is too large for a single box, We will contact you to see if you would like to pay for an additional package. Additional packages are $35.95 each. Insurance: Insurance is available for Foreign (non-Canadian) orders and maybe limited by some countries, Insurance can be purchased by stating in the comment section during checkout, we will email with additional costs or if no insurance is available for that specific country. Berea Hardwoods Co. Inc. assumes no liability for orders after they have been mailed. We can also ship UPS service at additional charges.Duties/Tarrifs/Fees/Etc All duties, tarrifs, and any other fees imposed by the local government and/or postal system are the sole responsibility of the buyer.
Due to postal regulations we cannot ship the following items overseas or to Alaska or Hawaii
- Hut Crystal Coat
Return Policy We, at The Berea Hardwoods Co. Inc., take great pride in the quality of our products. If you are not 100% satisfied with your purchase, you may return it within 30 days of purchase for a full refund of the purchase price. To return a product, please call or email our Customer Service Department at 877-736-5487 or email@example.com to obtain a Return Merchandise Authorization (RMA) number and shipping instructions. Write the RMA number on the outside of the box or envelope. Ship the product back to us and we will process your return promptly. Do not return any item to us without authorization. Unless the product being returned is defective or is not the item you ordered, you are responsible for the shipping charges incurred when returning any product. All items accepted for return must include all original instructions and packaging. Pen and project components will not be accepted for return unless originally purchased as components. Items that have been abused or modified from their original condition may not be accepted. Once your return is received and inspected (usually within 48 hours of receipt), your refund will be processed and a credit will be automatically applied to your credit card or original method of payment within 7 days. Please note that depending on your credit card issuer or bank, it may take an additional 2-10 business days after your credit is applied for it to post to your account.